The original shaft saver | ShaftSaverPro

ShaftSaverPro forms a protective layer between the graphite shaft and the edge of the golf bag.

Protect your shafts from bag wear

The ShaftSaverPro (measuring 5 cm and weighing approximately 2 grams) is placed on the contact zone between the shaft and the golf bag to absorb friction. This ensures that the ShaftSaverPro wears down instead of your shaft. Suitable for all graphite shafts of drivers, fairway woods, hybrids, and irons.

Protects graphite shafts against wear in the golf bag

The ShaftSaverPro wears, not your shaft

Fits all standard graphite shaft diameters

High-quality technical elastomer with an industrial adhesive layer: dimensionally stable and resistant to all weather conditions on the golf course.

Who is the ShaftSaverPro for?

The ShaftSaverPro is designed for golfers who want to protect their graphite shafts from wear in the golf bag and extend the lifespan of their clubs. Particularly for:

Drivers, fairway woods, irons, and hybrid graphite shafts

Golfers who take care of their equipment

Club fitters and golf shops looking to professionally protect their customers’ graphite shafts

Two golf bags with graphite shafts fitted with ShaftSaverPro.

Rules vs. Reality: For the win or for fun?

The R&A has officially designated the ShaftSaverPro as ‘non-conforming’. This means that the product may not officially be on the shaft during tournaments or handicap-qualifying rounds.
In practice: In a friendly round with your regular flight, the main priorities are enjoyment and the preservation of your valuable equipment. The ShaftSaverPro has no influence on your swing or ball flight.
The choice: Because the ShaftSaverPro is mounted with double-sided tape, it is intended for permanent use. Use during official tournaments is at your own risk.

Installation and Instructions

The ShaftSaverPro is quick to install. No tools required. Watch the instruction video.

Determine the wear point in the golf bag

Mark the position of the ShaftSaverPro with masking tape

Lightly sand the inside of the ShaftSaverPro

Degrease the shaft and the inside of the ShaftSaverPro

Apply the double-sided tape to the shaft

Center the ShaftSaverPro and press firmly

When should you replace the ShaftSaverPro?

You replace the ShaftSaverPro as soon as it shows visible wear at the point where it contacts the golf bag. This indicates it has done its job: the ShaftSaverPro wears, not your shaft. With a thickness of over 1.5 mm, it offers long-lasting protection. In practice, a single ShaftSaverPro lasts for years. Replacement is simple.

The ShaftSaverPro can be removed from your shaft in under a minute. Watch the video.

When is the ShaftSaverPro not suitable?

In certain situations, the ShaftSaverPro may not perform optimally:

The compartments in your golf bag are not of equal height and you do not have a fixed club arrangement
You use multiple golf bags with different dimensions
If you regularly adjust the loft of your club
If you are about to purchase a new bag, which will change the contact/wear point

Frequently Asked Questions

How large is the ShaftSaverPro?

The ShaftSaverPro is approximately 5 cm long. Small enough to be inconspicuous, large enough to protect the exact wear spot.

Does the ShaftSaverPro affect the ball flight?

In practice, golfers generally notice no difference. The ShaftSaverPro has undergone an initial blind test with a Trackman featuring a Pro who hits a 270-meter carry. He noticed no difference, and the statistics also showed that it made no difference.

Can I install the ShaftSaverPro myself?

Yes. The ShaftSaverPro can be attached in a few minutes using the included double-sided tape. No tools required. Watch the instructional video.

Can’t I just use a headcover with a long sock as a shaft protector?

You can, but in practice, it is somewhat inconvenient. It means that after every shot, you have to put that fabric sock back over the club and push it between the shaft and the bag. ShaftSaverPro solves this permanently without requiring any extra actions.

What should I do if my graphite golf shafts already have scratches from the bag rim?

If there are already scratches or noticeable damage on the shaft, the protective clear coat has been compromised. To prevent constant friction from damaging the graphite (carbon) even deeper and permanently weakening the club, you must stop the friction immediately. You can apply ShaftSaverPro directly over the existing damage using the double-sided tape to stop further wear and seal the area.

Doesn’t a golf bag with a soft rim (divider) help prevent damage to graphite shafts?

No, unfortunately, it doesn’t help. Because the clubhead always hangs to one side, gravity causes the shaft to rest continuously on the exact same point against the rim of the bag. While walking the course or riding a trolley, the shaft constantly rubs against this edge. This gradual friction slowly but surely wears down the clear coat, no matter how soft the bag’s rim is.

May I use the ShaftSaverPro during official competitions?

ShaftSaverPro has no noticeable effect on your swing or ball flight. However, under the R&A’s current interpretation, it does not comply with the rules for official competitions. This is a matter of the rules, not a playing advantage. Officially, it is therefore not allowed.

We play golf for enjoyment and want to protect our expensive clubs. That’s why we expect little discussion at regular club competitions. Golf’s rules also change as the sport evolves: steel shafts were once banned. Rangefinders were initially banned too, but were later allowed after their use had become widespread.

Does the ShaftSaverPro protect the entire shaft?

No. And that is exactly its strength. The ShaftSaverPro is only placed where the shaft touches the golf bag – where the wear occurs. This way, you protect the exact vulnerable point without unnecessary material or impact on your club.

What’s the difference between a travel shaft protector and ShaftSaverPro?

An umbrella-style shaft protector protects your clubs while they’re in a travel bag. ShaftSaverPro protects your graphite shafts from rubbing against the edge of your golf bag during your rounds. Together, they protect your clubs both while travelling and on the course.

How often should I replace the ShaftSaverPro?

The ShaftSaverPro wears down instead of your shaft. Depending on how often you play, one ShaftSaverPro usually lasts for years. Replacement is easy and costs only a few euros.

How is the ShaftSaverPro attached?

The ShaftSaverPro is attached using the included 3M double-sided tape. This acts as a strong, flexible adhesive: it stays firmly in place but can be removed and replaced later without damaging the shaft.

In what quantities is the ShaftSaverPro available?

The ShaftSaverPro is available in retail packaging in packs of 5. In the webshop, they are also available in packs of 13 or 50.

I have a golf shop and would like to order a larger quantity. Is that possible?

Yes. For golf shops and club fitters, larger quantities of ShaftSaverPro are available without packaging.
This allows you to install the ShaftSaverPro as standard on every graphite shaft sold. Please contact us.

Where can I buy the ShaftSaverPro?

More and more golf shops and golf pros are stocking the ShaftSaverPro. The launch has just begun, and we are rapidly expanding the network. You can now order the ShaftSaverPro directly from the webshop on this website.

Can the ShaftSaverPro cause wear to my golf bag?

Both the shaft and the ShaftSaverPro can cause wear to the golf bag in certain situations.